Panneau mural effet béton BétonFlex Ciment installé dans un loft

Install a BétonFlex concrete-look wall panel

BétonFlex panels combine a real concrete face with a flexible fibreglass backing. They go up with adhesive, on a straight wall as well as on a column or curved surface, using everyday tools.

This guide walks you through the 8 steps to install a concrete-look wall panel and, for each one, the products to use.

Walls · Ceilings · Curved surfaces · Indoor and outdoor

BétonFlex installation guide

How to install a concrete-look wall panel in 8 steps

For each step: what to do, the tools you need and the recommended products. The full guide is also available as a PDF (in French).

Installation d'un panneau mural effet béton BétonFlex : entreposage des panneaux à plat sur palette

Step 1 : Storage and handling

Well-stored panels go up on the wall in perfect condition. A few precautions are all it takes until installation day.

  • Store the panels flat.
  • Keep them in a dry place, away from moisture.
  • Protect them from sunlight and extreme temperatures.
  • Always lift panels vertically.
  • Never drag panels along the floor.

Still choosing a model? Order BétonFlex samples to see the texture in person.

The panel

  • Real concrete
  • Fibreglass backing
  • 2 to 3 mm thick
  • Size varies by model
  • Indoor and outdoor
  • Walls ceilings and curves
Installation d'un panneau mural effet béton BétonFlex : préparation et nettoyage du support

Step 2 : Surface preparation

The surface must be clean, dry, flat, stable and structurally sound.

  • Remove dust, grease and any loose particles.
  • Fix any major irregularities before installation.
  • Do not install behind a direct heat source.

Compatible substrates

  • Drywall
  • MDF
  • Plywood
  • OSB
  • Concrete
  • Brick and masonry
  • Fibre cement
  • Existing tile

Tools for this step

  • Clean cloth
Installation d'un panneau mural effet béton BétonFlex : découpe du panneau au couteau utilitaire

Step 3 : Measuring and cutting

  • Measure and mark the panel to the required dimensions.
  • Cut from the back of the panel whenever possible.
  • Mark all cuts before making the final cut.

To work out how many panels to order, use the calculator on each BétonFlex concrete-look wall panel product page.

Tools for this step

  • Tape measure
  • Pencil
  • Square
  • Straightedge
  • Utility knife
  • Angle grinder (diamond blade)
  • Circular saw
  • Safety glasses
  • Work gloves
Installation d'un panneau mural effet béton BétonFlex : application de l'adhésif en cordons au dos du panneau

Step 4 : Applying the adhesive

  • Double-sided application recommended: apply adhesive to the back of the panel and to the substrate.
  • Apply continuous beads 6 to 8 in. (15 to 20 cm) apart.
  • Use one of the high-quality construction adhesives recommended below.

Tools for this step

  • Caulking gun
  • Work gloves

Recommended products

Lepage PL Premium Max, adhésif de construction recommandé pour l'installation d'un panneau mural effet béton BétonFlex Adhesive

Lepage PL Premium Max

High-performance construction adhesive (266 ml)

Tremco Dymonic 100, adhésif polymère recommandé pour l'installation d'un panneau mural effet béton BétonFlex Adhesive

Tremco Dymonic 100

High-performance polymer adhesive

Tremco Dymonic FC, adhésif polymère recommandé pour l'installation d'un panneau mural effet béton BétonFlex Adhesive

Tremco Dymonic FC

High-performance polymer adhesive

Installation d'un panneau mural effet béton BétonFlex : pose du panneau sur le mur

Step 5 : Installing the panel

  • Install the panel from the bottom up.
  • Press firmly over the entire surface for good adhesion.
  • Check the alignment with a level.
  • Continue one panel at a time.
  • Avoid excessive humidity during installation.
  • Curved surfaces: bend the panel gradually, starting from the top, as with the Bulgari Roman Column panel.
  • Ceilings and curves: hold the panel in place with temporary supports until the adhesive has fully set.

Watch the installation on a flat surface and on a column

Tools for this step

  • Level
Installation d'un panneau mural effet béton BétonFlex : joint entre deux panneaux

Step 6 : Joints and finishing

Three finishes, depending on the look you want.

Option 1: invisible joint. Fill the joint with joint filler, sand lightly, then apply primer and paint.

Option 2: visible joint. Leave the joint visible for a raw, architectural concrete look.

Option 3: wax stick. Hide minor imperfections with a matching wax fill stick.

Some models can be painted for a more uniform finish. If paint would hide the concrete effect, choose option 2 or 3, followed by the sealer in step 7.

Recommended products

Enduit de bouchage pour béton Quikrete, filler à joint recommandé pour l'installation d'un panneau mural effet béton BétonFlex Finishing

Concrete joint filler

Option 1: fill the joint before sanding

Peinture Benjamin Moore AURA d'extérieur recommandée pour l'installation d'un panneau mural effet béton BétonFlex Paint

Benjamin Moore AURA® Exterior

Option 1: 100% acrylic paint, sold by Benjamin Moore retailers

Bâtons de cire de retouche recommandés pour l'installation d'un panneau mural effet béton BétonFlex Touch-up wax

Wax fill sticks

Option 3: hide small imperfections

Ruban de peintre ScotchBlue recommandé pour l'installation d'un panneau mural effet béton BétonFlex Painter's tape

Painter's tape

Protect the edges while finishing the joints

Installation d'un panneau mural effet béton BétonFlex : scellant à base d'eau Techniseal

Step 7 : Sealer (recommended)

  • The sealer protects the surface from stains and moisture, and makes cleaning easier.
  • Let the adhesive cure for at least 24 to 48 hours before applying the sealer, once the installation is complete.
  • Seal the cut edges as well.

Outdoors, your choice of sealer determines how well the panel holds up over time.

Recommended products

Scellant à base d'eau Techniseal recommandé pour l'installation d'un panneau mural effet béton BétonFlex Sealer

Techniseal water-based sealer

Water-based sealer for natural stone and concrete

Scellant Stain-Proof de Dry-Treat recommandé pour l'installation d'un panneau mural effet béton BétonFlex Sealer

Stain-Proof by Dry-Treat

High-performance penetrating sealer

Scellant Aqua Mix Sealer's Choice Gold recommandé pour l'installation d'un panneau mural effet béton BétonFlex Sealer

Aqua Mix Sealer's Choice Gold

Water-based sealer for natural stone

Installation d'un panneau mural effet béton BétonFlex : résultat final sur un mur courbe

Step 8 : Final result and care

The result: an elegant, durable and timeless concrete-look wall that needs very little maintenance.

  • Clean with a soft, dry cloth, or with mild soap and water.
  • Avoid abrasive, acidic or solvent-based products and harsh chemicals.

Looking for other materials? Discover our stone wall panels and our interior wall cladding ideas. Have a project to discuss? Book a showroom visit or request a quote.

Tools for this step

  • Clean cloth

Complementary products are available from retailers in Quebec and across Canada

Video

Flat or curved surface: watch the installation

Flat surface

A straight wall in a restaurant

Adhesive, placement, result: installing the BétonFlex Granite Black flexible panel in under 20 seconds.

See the Granite Black panel

Curved surface

A marble-look column

The BétonFlex Bulgari Roman Column flexible panel wraps around a round column: adhesive, placement, result.

See the Bulgari Roman Column panel

Choose your BétonFlex panel

View all

Installation FAQ

It's a thin, flexible panel made of a real concrete face on a fibreglass-reinforced composite backing. It gives the look of a concrete, stone or marble wall without formwork or masonry, and installs with adhesive on a straight wall, a ceiling or a curved surface. See all BétonFlex concrete-look wall panels.

Yes. The surface is real concrete, which gives it a natural texture and variations in tone. The flexible fibreglass backing lets you bend the panel and install it with adhesive.

The panel is about 2 to 3 mm thick (1/16 to 1/8 in.). The size varies by model and is listed on each product page.

Yes. The panels go up with adhesive and everyday tools: utility knife, straightedge, level and caulking gun. For larger projects in Greater Montreal, we also offer an installation service: request a quote.

A high-performance construction adhesive: LePage PL Premium Max, Tremco Dymonic 100 or Tremco Dymonic FC. Apply it to both the back of the panel and the substrate, in continuous beads 6 to 8 in. (15 to 20 cm) apart.

Drywall, MDF, plywood, OSB, concrete, brick or masonry, fibre cement and existing tile. The surface must be clean, dry, flat, stable and structurally sound.

Yes. Existing tile is a compatible substrate, as long as it is clean, dry, flat and firmly attached.

A utility knife and straightedge, an angle grinder with a diamond blade, or a circular saw. Cut from the back of the panel whenever possible and mark all cuts before making the final cut.

The panel is flexible: bend it gradually, starting from the top, press it firmly over the entire surface and hold it with temporary supports until the adhesive dries. The Bulgari Roman Column panel was designed for columns.

Yes. On a ceiling, hold the panels with temporary supports until the adhesive has fully set.

Yes, BétonFlex can be used indoors and outdoors, depending on the sealer. Outdoors, apply a recommended sealer (Techniseal, Stain-Proof by Dry-Treat or Aqua Mix) over the entire surface, including the cut edges.

Yes. The panel has low water absorption and stays stable in humid rooms. Apply a sealer to protect the surface from stains and moisture, and don't install it directly behind a heat source such as a stove. For an area directly exposed to water, such as a shower, contact us before installation.

BétonFlex is made of mineral materials and has been tested for fire performance (see our certifications). However, it should not be installed directly behind a heat source.

Let the adhesive cure for at least 24 to 48 hours after installation. Apply the sealer once the whole installation is complete.

Fill the joint with a concrete joint filler, sand lightly, then apply primer and paint. There are two other options: leave the joint visible for a raw concrete look, or hide small imperfections with a matching wax fill stick.

Some models can be primed and painted for a more uniform finish. We recommend Benjamin Moore AURA® Exterior (100% acrylic, high performance). On models where paint would lose the concrete effect, use a sealer instead.

Clean with a soft, dry cloth, or with mild soap and water. Avoid abrasive, acidic or solvent-based products and harsh chemicals.

Polished plaster and microcement are applied on site in several coats, with drying time between them. BétonFlex arrives as ready-to-install panels: glue them in place, finish the joints, then apply a sealer. The look is consistent from panel to panel, and the panels also work on curved surfaces.

The size varies by model. The calculator on each product page estimates the number of panels based on your wall's dimensions. See the BétonFlex concrete-look wall panels.

Yes. You can order samples or book a showroom visit in Montreal to see and touch the models.

The recommended adhesives, sealers and accessories are available from hardware and home improvement stores in Quebec and across Canada, in store and online. Purchase links are listed at each step of the guide.

Yes, the BétonFlex installation guide is available as a PDF (in French), ready to print for the job site.